Thank you for the picture!
Beiträge von vdm
-
-
Hey Scotti, do you have a picture where you put the box in the scooter?
-
Hello everyone, I still have a question about this batterypack.
To have 96V the batterys have to be in serie. But then you need a 94V charger.
With a 12V charger, do you always disconnect every battery, charge them seperately en reconnect everything again? Is that the only way?
-
Thank you for the info gride! I really appreciate you helping me out!
Some more questions:- I allready let the air out of the tire
, I will inflate it back again, at which bar should I inflate?
- Would it be bad to replace the iron wheel for a plastic one, since I will use battery power I will have no need for it?
- Is it normal that I do not have a brush? I see you have 2 iron wheels how come?I will keep you updated!
Ty
VDM
-
-
-
Hey Gride,
I added some pics, I want to remove the complete body from the bumper car, because the whole thing needs to be cleaned, there is probally 1 cm of dirt inside of it.
Could you tell me how to remove the body? If let the air out of the tire. Do I have to remove the tire? And which nut/bolts do I need to remove?
I marked 2 bolts in the picture with a red circle, are these the nuts that need to removed?Some other things I noticed.
- The lights were ducktaped, they have not sockets. They were also not connected to the electrical system of the autoskooter. They were just hanging there.
- 1 tire is completly gone, just iron.
- Some loose wires
- Lots lots of dirtI'm going to measure out the motor and contactor tonight and see if I have any resistence.
-
Hello Gride,
I had to cut the 2 bolts, the nuts were to rusted, not even WD-40 could get them off.
About the electronics, I am not sure everything is still working, you say the contactor is mostly out of order, is there anyway to test this? I am waiting for my batteries, but it will take 2 weeks till I get them so I can not test all the electronics. I am going to take some pics tonight and post them here, maybe you will see something that is not good.
Vdm
-
Just tried to remove the two nuts on the l-shaped bolt. The frist one came off but the second one is really rusted on the bolt, I put some WD-40 on it. So I think now just have to wait? If you have any hints to remove these old nuts, I am listening :).
-
Thank you for all this info! Im going to start take it apart today! Thanks again.
Vdm
-
I dont understand any of this, but im following it!! Good job!!
-
Hello gride,
Thank you for the info, yes I have some pictures I introduced myself in "Vorstellungen neuer User" you can see my welcome there!
I do have some other question for you.
I am planning on doing a complete restoration.- How do you take the seat apart? Do you just pull out the seats or are they bolted somewhere.
- I do not have a key for my tokenbox, do you have a technique to open it? (Where can I buy a new one?)
- If you want to work on the bodem of you scooter, do you have tools to lift it up, or do you tilt it over?Ty!
-
Gride thank you for your feedback, I will not go higher than maybe 108V (9x12V) so that will not be a problem. Sorry for the maybe stupid question but what is a brush collector? I am new to this. TY!
-
Hi i could speak English (And French also ! cause i'am)
Ok with your drawing, about the resistor you can keep it (This have been put by Reverchon in order to set the speed of the car, when a showman have differnet kind of car (old one / new one) or Reverchon and others cars like Bertazzon, ...
If you remove it you will just increase the motor speed.
Hello, I did not know the resistor was to limit the speed, I knew autoscooters had a working voltage of 80-110V so I thought you could increase the speed by increasing the voltage.
Question for you, do you also use batterys for your autoscooter, if so, how do you charge them?
-
Yes Totti if you want, because i cannot find him. Ty!
-
Thank you totti!
-
Hello Stefan,
Yes the bumper is damaged in front, the rubber is cracked, 475€ woaw that is disastrous since I only paid 400€ for this scooter :/. Everything is still there, motor etc. I think I can repair the rubber with some sort or liquid rubber, the problem there is, that you will see a colour difference, but Im planning on repairing the cracked rubber, and then overcoating the complete bumper so the colour is the same.
Thank you for the reference 'gride' ill contact him if I have questions. -
Hello everyone, I hope some people speak english here, I am from Belgium, just recently bought a 1978 Reverchon Jubileè.
I am going to restore it. But first I would like to connect a batterie to the electromotor to make it run autonomously.
I made a picture how to connect the batteries, can someone look at it, and tell me if this is correct, or maybe I forgot something.
Also, should I change the resistor that is connected to the contactor.
Thank you very much!Vdm
-
Hello, thank you for responding I will surely check your thread out, I tried uploading as you sayed I hope you can see the pictures.
I allready did some research about the scooter, its a Reverchon Jubilieé from 1978 Orange. I hope you can see the pictures.
It was displayed as a gimmickk in a famous TV show here.
They rewirred some stuff to make the lights work on 230V
There is also some damage to the bumper, I hope I can fix that.greets vdm
-
Hello everyone, I am vdm from Belgium, like to say hello here. I have just bought my first autoscooter, the intention is to make it run autonomously. I hope I can get some help here.
Thank youIch spreche kein Deutsch
